We gratefully acknowledge support from
the Simons Foundation and member institutions.

Applied Physics

New submissions

[ total of 15 entries: 1-15 ]
[ showing up to 2000 entries per page: fewer | more ]

New submissions for Wed, 23 Sep 20

[1]  arXiv:2009.10101 [pdf, other]
Title: Dielectric loss in epitaxial Al/GaAs/Al trilayers for superconducting circuits
Subjects: Applied Physics (physics.app-ph); Quantum Physics (quant-ph)

Epitaxially-grown superconductor/dielectric/superconductor trilayers have the potential to form high-performance superconducting quantum devices and may even allow scalable superconducting quantum computing with low-surface-area qubits such as the merged-element transmon. In this work, we measure the power-independent loss and two-level-state (TLS) loss of epitaxial, wafer-bonded, and substrate-removed Al/GaAs/Al trilayers by measuring lumped element superconducting microwave resonators at millikelvin temperatures and down to single photon powers. The power-independent loss of the device is $(4.8 \pm 0.1) \times 10^{-5}$ and resonator-induced intrinsic TLS loss is $(6.4 \pm 0.2) \times 10^{-5}$. Dielectric loss extraction is used to determine a lower bound of the intrinsic TLS loss of the trilayer of $7.2 \times 10^{-5}$. The unusually high power-independent loss is attributed to GaAs's intrinsic piezoelectricity.

[2]  arXiv:2009.10225 [pdf]
Title: Fully printed, all-carbon, recyclable electronics
Comments: 16 pages, 3 figures
Subjects: Applied Physics (physics.app-ph); Materials Science (cond-mat.mtrl-sci)

The rapid growth of electronic waste must be curtailed to prevent accumulation of environmentally and biologically toxic materials, which are essential to traditional electronics. The recent proliferation of transient electronics has focused predominantly on biocompatibility, and studies reporting material recapture have only demonstrated reuse of conducting materials. Meanwhile, the ideal solution to the electronic waste epidemic-recapture and reuse of all materials-has been largely neglected. Here we show complete recyclability of all materials in printed, all-carbon electronics using paper substrates, semiconducting carbon nanotubes, conducting graphene, and insulating crystalline nanocellulose. The addition of mobile ions to the dielectric produced significant improvements in switching speed, subthreshold swing, and among the highest on-current for printed transistors. These devices evinced superlative stability over 6 months, after which they are shown to be controllably decomposed for complete recycling of materials and re-printing of devices with similar performance to baseline devices. The printing of all-carbon, recyclable electronics presents a new path toward green electronics with potential to mitigate the environmental impact of electronic waste. We anticipate all-carbon, recyclable electronics to be a watershed, facilitating internet-of-everything applications, such as ubiquitous sensors for continuous monitoring of diseases or environmental conditions, while preserving carbon neutrality in the device lifecycle.

[3]  arXiv:2009.10230 [pdf, other]
Title: REPORT: Investigation on Curvilinear Anisotropy via Isogeometric Analysis (IGA)
Subjects: Applied Physics (physics.app-ph)

The advent of multi-material additive manufacturing and automated composite manufacturing has enabled the design of structures featuring complex curvilinear anisotropy. To take advantage of the new design space, efficient computational approaches are quintessential. In this study, we explored a new NURBS-based Isogeometric Analysis (IGA) framework for the simulation of curvilinear fiber composites and we compared it to standard Finite Element Analysis (FEA). A plate featuring a semi-circular notch under tensile loading with different fiber configurations served as a case study. We showed that, thanks to the exact geometric representation and the enriched continuity between elements, NURBS-based IGA outperforms classical FEA in terms of computational efficiency, time-consumption, and estimation quality of field variables for same number of degrees-of-freedom. To further demonstrate the use of the IGA framework, we performed optimization studies aimed at identifying the fiber paths minimizing stress concentration and Tsai-Wu failure index. The model showed that curvilinear anisotropy can be effectively harnessed to reduce the stress concentration of up to 82 % compared to unidirectional composites without affecting the overall plate stiffness significantly.

[4]  arXiv:2009.10293 [pdf, other]
Title: Au-decorated black TiO$_2$ produced via laser ablation in liquid
Comments: 10 pages, 5 figures
Subjects: Applied Physics (physics.app-ph)

Rational combination of plasmonic and all-dielectric concepts within unique hybrid nanomaterials provides promising route toward devices with ultimate performance and extended modalities. However, spectral matching of plasmonic and Mie-type resonances for such nanostructures can only be achieved for their dissimilar characteristic sizes, thus making the resulting hybrid nanostructure geometry complex for practical realization and large-scale replication. Here, we produced unique amorphous TiO$_2$ nanospheres simultaneously decorated and doped with Au nanoclusters via single-step nanosecond-laser ablation of commercially available TiO$_2$ nanopowders dispersed in aqueous HAuCl$_4$. The fabricated hybrids demonstrate remarkable light-absorbing properties (averaged value $\approx$ 96%) in the visible and near-IR spectral range mediated by bandgap reduction of the laser-processed amorphous TiO$_2$, as well as plasmon resonances of the decorating Au nanoclusters, which was confirmed by combining optical spectroscopy, advanced electron energy loss spectroscopy, transmission electron microscopy and electromagnetic modeling. Excellent light-absorbing and plasmonic properties of the produced hybrids were implemented to demonstrate catalytically passive SERS biosensor for identification of analytes at trace concentrations and solar steam generator that permitted to increase water evaporation rate by 2.5 times compared with that of pure water under identical one-sun irradiation conditions.

[5]  arXiv:2009.10299 [pdf]
Title: Magnon-mediated spin currents in Tm3Fe5O12/Pt with perpendicular magnetic anisotropy
Subjects: Applied Physics (physics.app-ph); Materials Science (cond-mat.mtrl-sci)

The control of pure spin currents carried by magnons in magnetic insulator (MI) garnet films with a robust perpendicular magnetic anisotropy (PMA) is of great interest to spintronic technology as they can be used to carry, transport and process information. Garnet films with PMA present labyrinth domain magnetic structures that enrich the magnetization dynamics, and could be employed in more efficient wave-based logic and memory computing devices. In MI/NM bilayers, where NM being a normal metal providing a strong spin-orbit coupling, the PMA benefits the spin-orbit torque (SOT) driven magnetization's switching by lowering the needed current and rendering the process faster, crucial for developing magnetic random-access memories (SOT-MRAM). In this work, we investigated the magnetic anisotropies in thulium iron garnet (TIG) films with PMA via ferromagnetic resonance measurements, followed by the excitation and detection of magnon-mediated pure spin currents in TIG/Pt driven by microwaves and heat currents. TIG films presented a Gilbert damping constant {\alpha}~0.01, with resonance fields above 3.5 kOe and half linewidths broader than 60 Oe, at 300 K and 9.5 GHz. The spin-to-charge current conversion through TIG/Pt was observed as a micro-voltage generated at the edges of the Pt film. The obtained spin Seebeck coefficient was 0.54 {\mu}V/K, confirming also the high interfacial spin transparency.

[6]  arXiv:2009.10393 [pdf]
Title: Cryogenic cleaning of tin-drop contamination on surfaces relevant for extreme ultraviolet light collection
Comments: 23 pages, 9 figures
Subjects: Applied Physics (physics.app-ph)

Improvement of tool reliability and uptime is a current focus in development of extreme ultraviolet lithography. The lifetime of collection mirrors for extreme ultraviolet light in tin-based plasma light sources is limited considerably by contamination with thick tin deposits that cannot be removed sufficiently fast by plasma etching. For tin droplet splats sticking to large substrates, we have developed and compared several efficient cleaning techniques based on cryogenic cooling. A silicon carbide substrate and different silicon wafer samples with up to 6 inch diameter with the surface uncoated, multilayer-coated, unstructured and grating-structured were tested. After tin dripping onto heated samples, embrittlement of droplet contamination is induced in-situ by stresses during phase transformation, following the initiation of tin pest with seed crystals of gray tin. Conversion of initially adhesive deposits to loose gray tin has been reached in less than 24 hours on all tested surfaces by continuous cooling with cold nitrogen vapor to temperatures in the range of -30 to -50 {\deg}C. Alternatively, stress-initiated tin-removal by delamination of beta-Sn droplet splats has been attained via contraction strain induced by strong cooling to temperatures of around -120 {\deg}C. Profilometry has been used to analyze the bottom side of tin droplet splats removed from a grating-structured wafer. The in-situ tin cleaning techniques give results comparable to fast ex-situ cleaning that has been achieved either by sample immersion in liquid nitrogen or by splat removal after CO2 snowflake aerosol impact using a hand-held jet-nozzle. The implementation of the in-situ phase-conversion concept for the cleaning of collector mirrors in commercial light sources for lithography is discussed.

[7]  arXiv:2009.10462 [pdf]
Title: Convective Heat Transfer and Pressure Drop Characteristics of Graphene-Water Nanofluids in Transitional Flow
Subjects: Applied Physics (physics.app-ph); Fluid Dynamics (physics.flu-dyn)

The convective heat transfer and flow behavior of graphene-water nanofluids are studied experimentally by focusing on transitional flow. Graphene-water nanofluids with different particle mass fractions (0.025, 0.1 and 0.2%) are produced following two-step method and using PVP as a surfactant. Thermo-physical characterization is performed by measuring viscosity and thermal conductivity of the nanofluids. Convection characteristics are experimentally studied from laminar to turbulent flow regimes. It is seen that pressure drop increases dramatically in the transition region, and laminar to turbulent transition shifts to lower Reynolds numbers with increasing nanoparticle concentration. The transition initiates at a Reynolds number of 2475 for water, while it initiates at 2315 for the nanofluid with 0.2% particle mass fraction. Increase in mean heat transfer coefficient and Nusselt numbers are nearly identical at different Reynolds numbers and axial positions along the test tube in the laminar flow for nanofluids and water due to dominance of conduction enhancement mechanisms on the heat transfer increase in laminar flow. Beyond laminar flow regime, enhancement of Nusselt number is observed indicating that thermophoresis and Brownian motion are more effective heat transfer augmentation mechanisms. The maximum heat transfer enhancement is observed as 36% for a Reynolds number of 3950.

[8]  arXiv:2009.10560 [pdf]
Title: Outgassing rate comparison of seven geometrically similar vacuum chambers of different materials and heat treatments
Authors: James A. Fedchak (1), Julia K. Scherschligt (1), Sefer Avdiaj (2), Daniel S. Barker (1), Stephen P. Eckel (1), Ben Bowers (3), Scott OConnell (3), Perry Henderson (3) ((1) National Institute of Standards and Technology (NIST), Gaithersburg, (2) University of Prishtina, Kosova, (3) Anderson Dahlen Applied Vacuum Division)
Comments: 27 pages, 7 figures, 3 tables The following article has been submitted the Journal of Vacuum Science & Technology A. After it is published, it will be found at this https URL
Subjects: Applied Physics (physics.app-ph); Instrumentation and Detectors (physics.ins-det)

We have measured the water and hydrogen outgassing rates of seven vacuum chambers of identical geometry but constructed of different materials and heat treatments. Chambers of five different materials were tested: 304L, 316L, and 316LN stainless steels; titanium; and aluminum. In addition, chambers constructed of 316L and 316LN stainless steel were subjected to a vacuum-fire process, where they were heated to approximately 950 {\deg}C for 24 hours while under vacuum. These latter two chambers are designated as 316L-XHV and 316LN-XHV. Because all the chambers were of identical geometry and made by the same manufacturer, a relative comparison of the outgassing rates among these chambers can be made. Water outgassing rates were measured as a function of time using the throughput technique. The water outgassing results for the 316L, 316LN, 316L-XHV, 316LN-XHV were all similar, but lower than those of 304L by a factor of 3 to 5 lower at 10,000 s. The water outgassing results for Ti and Al chambers were closer to that of 304L, Ti being slightly lower. Hydrogen outgassing rates were measured using the rate-of-rise method and performed after a low-temperature bake of 125 {\deg}C to 150 {\deg}C for a minimum of 72 hours. The Ti, Al, 316L-XHV, and 316LN-XHV chambers all have ultra-low specific outgassing rates below 1.0E-11 Pa L s-1 cm-2 and are a factor of 100 or better than the 304L chamber. The 304L, 316L, and 316LN chambers with no vacuum-fire heat treatment have larger hydrogen outgassing rates than the other chambers, with determined specific outgassing rates ranging between 4.0E-11 Pa L s-1 cm-2 and 8.0E-11 Pa L s-1 cm-2. We conclude that Ti, Al, 316L-XHV, and 316LN-XHV have hydrogen outgassing rates that make them excellent choices for ultra-high vacuum (UHV) and extreme-high vacuum (XHV) applications, the choice depending on cost and other material properties.

Cross-lists for Wed, 23 Sep 20

[9]  arXiv:2009.10335 (cross-list from physics.optics) [pdf, other]
Title: General optical metrology for the dipole orientation in organic light-emitting diodes
Comments: 14 pages, 3 figures
Subjects: Optics (physics.optics); Applied Physics (physics.app-ph)

Considerable progress has been made in organic light-emitting diodes (OLEDs) to achieve high external quantum efficiency (EQE), among which the dipole orientation of OLED emitters has a remarkable effect. In most cases, EQE of the OLED emitter is theoretically predicted with only one orientation factor to match with corresponding experiments. Here, we develop a distribution theory with three independent parameters to fully describe the relationship between dipole orientations and power densities. Furthermore, we propose an optimal experiment configuration for measuring such distribution parameters. Measuring the unpolarized spectrum extremely can dig more information of dipole orientation distributions with a rather simple way. Our theory provides a universal plot of the OLED dipole orientation, paving the way for designing more complicated OLED structures.

[10]  arXiv:2009.10402 (cross-list from cond-mat.mtrl-sci) [pdf]
Title: Giant piezoresistive effect and strong band gap tunability in ultrathin InSe upon biaxial strain
Comments: 5 main text figures, 1 table comparing the strain tunable bandgap for different 2Ds and 11 supporting information figures
Subjects: Materials Science (cond-mat.mtrl-sci); Mesoscale and Nanoscale Physics (cond-mat.mes-hall); Applied Physics (physics.app-ph)

The ultrathin nature and dangling bonds free surface of two-dimensional (2D) semiconductors allow for significant modifications of their band gap through strain engineering. Here, thin InSe photodetector devices are biaxially stretched, finding, a strong band gap tunability upon strain. The applied biaxial strain is controlled through the substrate expansion upon temperature increase and the effective strain transfer from the substrate to the thin InSe is confirmed by Raman spectroscopy. The band gap change upon biaxial strain is determined through photoluminescence measurements, finding a gauge factor of up to ~200 meV/%. We further characterize the effect of biaxial strain on the electrical properties of the InSe devices. In the dark state, a large increase of the current is observed upon applied strain which gives a piezoresistive gauge factor value of ~450-1000, ~5-12 times larger than that of other 2D materials and of state-of-the-art silicon strain gauges. Moreover, the biaxial strain tuning of the InSe band gap also translates in a strain-induced redshift of the spectral response of our InSe photodetectors with {\Delta}Ecut-off ~173 meV at a rate of ~360 meV/% of strain, indicating a strong strain tunability of the spectral bandwidth of the photodetectors.

[11]  arXiv:2009.10501 (cross-list from eess.SP) [pdf, other]
Title: Modeling of Vertical Dipole Above Lossy Dielectric Half-Space: Characteristic Mode Theory
Comments: 23 pages, 5 Figures
Subjects: Signal Processing (eess.SP); Applied Physics (physics.app-ph)

This work introduces a theoretical extension of the characteristic mode formulation for analysing the vertical electric dipole lying above a lossy dielectric half-space. As the conventional characteristic formulation fails to maintain the orthogonality of the characteristic field modes over the infinite sphere, an alternate modal formulation is proposed here to maintain the orthogonality for both the current and field modes. The modal results are found to match closely with its method of moment counterparts. Later, the modes of an isolated dipole with no ground plane have been used to predict the role of the lossy ground plane through a theory of the linear combination of the eigenvectors. The proposed formulations have been studied with different heights from the ground plane and are compared with the direct modal solutions to validate its accuracy. It helps to provide a thorough understanding of how the isolated modes interact among each other to constitute the perturbed modes in the presence of the lossy half-space. It can find application to include the lossy earth effect in the study of the lightning fields and the path loss modelling of the antennas over the lossy ground.

[12]  arXiv:2009.10508 (cross-list from cond-mat.mes-hall) [pdf, other]
Title: Anomalous topological edge states in non-Hermitian piezophononic media
Subjects: Mesoscale and Nanoscale Physics (cond-mat.mes-hall); Applied Physics (physics.app-ph)

The bulk-boundary or bulk-edge correspondence is a principle relating surface confined states to the topological classification of the bulk. By combining non-Hermitian ingredients in terms of gain or loss with media that violate reciprocity, an unconventional non-Bloch bulk-boundary correspondence leads to unusual localization of bulk states at boundaries$-$a phenomenon coined non-Hermitian skin effect. Here we \textcolor{black}{numerically} employ the acoustoelectric effect in electrically biased and layered piezophononic media as a solid framework for non-Hermitian and nonreciprocal topological mechanics in the MHz regime. Thanks to a non-Hermitian skin effect for mechanical vibrations, we find that the bulk bands of finite systems are highly sensitive to the type of crystal termination, which indicates a failure of using traditional Bloch bands to predict the wave characteristics. More surprisingly, when reversing the electrical bias, we unveil how topological edge and bulk vibrations can be harnessed either at the same or opposite interface. Yet, while bulk states are found to display this unconventional skin effect, we further discuss how in-gap edge states in the same instant, counterintuitively are able to delocalize along the entire layered medium. We foresee that our predictions will stimulate new avenues in echo-less ultrasonics based on exotic wave physics.

Replacements for Wed, 23 Sep 20

[13]  arXiv:1903.11705 (replaced) [pdf]
Title: Polarization-sensitive and broadband photodetection based on a mixed-dimensionality TiS3/Si p-n junction
Comments: 6 main text figures, 1 figure. Includes the supporting information (18 supp. info. figures)
Journal-ref: Advanced Optical Materials, 2018, vol. 6, no 19, p. 1800351
Subjects: Applied Physics (physics.app-ph); Mesoscale and Nanoscale Physics (cond-mat.mes-hall); Materials Science (cond-mat.mtrl-sci)
[14]  arXiv:2002.10608 (replaced) [pdf]
Title: Strain-Tuned Magnetic Anisotropy in Sputtered Thulium Iron Garnet Ultrathin Films and TIG/Au/TIG Valve Structures
Comments: The following article has been accepted by Journal of Applied Physics
Journal-ref: Journal of Applied Physics 127, 115302 (2020)
Subjects: Applied Physics (physics.app-ph); Materials Science (cond-mat.mtrl-sci)
[15]  arXiv:2005.13949 (replaced) [pdf, other]
Title: High-yield wafer-scale fabrication of ultralow-loss, dispersion-engineered silicon nitride photonic circuits
Subjects: Applied Physics (physics.app-ph); Optics (physics.optics)
[ total of 15 entries: 1-15 ]
[ showing up to 2000 entries per page: fewer | more ]

Disable MathJax (What is MathJax?)

Links to: arXiv, form interface, find, physics, recent, 2009, contact, help  (Access key information)